RGS - Router Sled Dust Collection Shroud
RGS - Router Sled Dust Collection Shroud in Movement
RGS - Router Sled Dust Collection Shroud Base
RGS - Router Sled Dust Collection Shroud
RGS - Router Sled Dust Collection Shroud in Movement
RGS - Router Sled Dust Collection Shroud Base

RGS - Dust Collection Shroud

Add effective dust collection and containment to your existing Router Gantry System unit or as an add-on to new units!

With the strip brushes contacting the work surface, expect collection to exceed 90%.

  • Dual sided vacuum pick up
  • Clear polycarbonate for visibility
  • Full circumference containment with 2 inch bristle length brushes
  • Includes everything from the brushes all the way up to the 2-1/2 to 4 inch wye fitting
  • Reduces width capacity by 4 inches
$ 249.99 USD
/
  • 90-Day Money Back Guarantee 90-Day Money Back Guarantee
  • Lifetime Warranty Lifetime Warranty
  • Unlimited Phone & Email Support Unlimited Phone & Email Support
  • Clean, Consistent Cuts Every Time Clean, Consistent Cuts Every Time
  • Precision Tools, American Made Precision Tools, American Made
RGS - Router Sled Dust Collection Shroud
RGS - Router Sled Dust Collection Shroud in Movement
RGS - Router Sled Dust Collection Shroud Base

RGS - Dust Collection Shroud

$ 249.99
/
$ 249.99 USD
/

Product Reviews

What our customers say

Customer Reviews

Based on 10 reviews
80%
(8)
10%
(1)
10%
(1)
0%
(0)
0%
(0)
R
Roger Roberts
Awesome

Your table is awesome. My problem is learning how to set my new plunge router and dust on narrow boards. But the table is awesome 👌.
I've been cutting walnut lumber 1.25 thick 8 to 16 in. Wide it does a good job

L
Lonnie Koehne
Perfect

Little bit of work on assembly and install a complete vacuum piping for it but well worth it. Had done a piece without and did a similar piece with it and was practically nothing to sweep up. Definitely worth it.

D
David Cantwell
It helps

Having had the gantry system for a while I've enjoyed how great it works. The one issue was the amount of dust all over the place, including back in my face. Adding the dust collection shroud seemed a no brainer. It does keep the dust down in the shop and it stops the dust from coming back in my face. However, I mostly work with thinner pieces of material (1 or 2 feet wide by up to 8 feet long) the shroud itself has a wide footprint, most of the time one end or the other is not over the material and most of the larger dust shoots out any opening left available. Overall, the recovery of material is low, probably under 20%, but it does keep the smaller particles from traveling all over the shop and deflects most material down and away. Also as mentioned by others, you lose a few inches of travel on either end.

Hi David!

If the brushes are not in contact with a surface of some type there’s virtually no way to control the dust, so I’m not surprised that it doesn’t collect well on narrow boards. It’s effectively trying to pull a vacuum in a completely open environment.

When running narrow stock that doesn’t allow for a good seal between the material and shroud brushes you can place a thin sheet of plywood or similar material under the stock being planed so that the brushes aren’t hanging out over open air to allow a proper vacuum to form. With a decent seal you should be getting 90%+ collection with a dust collector pulling at least 800CFM. A shopvac or small collector won’t move enough volume.

We also have 3 inch long strip brushes available if the standard 2 inch brushes aren’t long enough.

Thank you for taking the time to leave feedback, it’s greatly appreciated!

-Jacob

C
Cole Ores

Awesome piece of equipment love the simplicity

S
Shawn Vasseur
Router sled dust collection

This works great. About 95% less mess. Great product.

12

Customers Also Viewed

View all products

90 Day Returns

If you don't love your TrueTrac product or you've ordered the wrong thing, simply let us know, send it back within 90-days and we'll give you a replacement or prompt refund. No questions asked.

TRUETRAC TRIPLE ‘C’ GUARANTEE

Our precision made tools, kits and systems are designed to give you Clean Consistent Cuts every time whether you're ripping plywood sheets or flattening rough cut lumber slabs. If they ever let you down because of an equipment failure on our part, just let us know and we'll bend over backwards to make things right.

LIFETIME GUARANTEE

We stand behind our products and want you to use them to make beautiful, heirloom pieces for years to come. If something breaks, we'll send a replacement straight away.

TELEPHONE SUPPORT

Got a question? Speak to one of our woodworking experts anytime between 9-6 Eastern and ask us anything about our products, how to set them up or how to get the best out of them.

Precision Made in Ohio, USA

We're proud to be American. Our family-owned production facility is located in Southern Ohio. We source nearly all our materials and components from Ohio too.